Quadra-Fire QVI35 Owner's Manual download pdf (Page 21)

Quadra-Fire • QVI-35FB-S • 2178-900 Rev. D • 9/09 21

B. Venting Components

CAUTION! Risk of Cuts/Abrasions/Flying Debris.

Wear protective gloves and safety glasses during instal-

lation. Sheet metal edges are sharp.

The vertical vent termination system installed on this model

includes:

• One 3-foot section stainless steel ﬂ exible pipe (included

with insert).

• Flexible vent pipe for exhaust air (included with vent kit).

• One length of 3-inch ﬂ exible vent pipe for combustion

air (included with vent kit).

• One pipe-to-cap adaptor (included with vent kit).

• One vertical termination cap (included with vent kit).

Installing Vent Pipe and Appliance

Figure 8.1

C. Connecting Vent Pipe

Reference instructions in the termination kit.

• Install the 3-inch ﬂ exible vent pipe(s) down through the

chimney.

• Secure the exhaust ﬂ exible vent pipe to the 3 foot section

stainless steel flexible vent pipe using the factory-

installed 3-inch collar in the stainless steel section of

pipe (see Figure 8.1).

• Use 3 screws to attach either a 4 foot or 30 foot section

of inlet air vent to the inlet collar on the collar slide plate

(see Figure 8.1). NOTE: The collar slide plate may be

removed from appliance to aid installation.

WARNING! Risk of Fire/Explosion/Asphyxiation! Do

NOT connect this gas appliance to a chimney ﬂ ue serving

a separate solid fuel or gas burning appliance.

• May impair safe operation of this appliance or other

appliances connected to the ﬂ ue.

• Vent this appliance directly outside.

• Use separate vent system for this appliance.

Horizontal venting is NOT allowed.

Vertical terminations are measured to top of chimney.

This appliance is listed for use with LINK-DV systems

and components only. It is permissible to extend venting

above existing chimney (within speciﬁ ed maximum verti-

cal limits) using SL-D series or Dura Vent GS series 4 in.

x 6-5/8 in. gas direct-vent pipe. Connection is made us-

ing SRVLINK-ADP. The vent must be terminated with the

cap supplied with the LINK-series vent kit.

A. Vent Limits

The abbreviations listed in this vent table key are used in

the vent diagrams.

Description

Minimum Vertical Run Length 14 ft.

Maximum Vertical Run Length 50 ft.

CAUTION! ALL vent speciﬁ cations MUST be followed.

This product is tested and listed to these speciﬁ cations.

Appliance performance will suffer if speciﬁ cations are not

followed.

TERMINATION

CAP

ADAPTOR

EXHAUST

VENT PIPE

V= 14 FT. MINIMUM

50 FT. MAXIMUM

3 INCH COLLAR

(Factory installed to

stainless steel section)

WARNING: DO NOT

BLOCK PIPE END WITH

INSULATION OR ANY OTHER

SEALING MATERIAL

STAINLESS STEEL

PIPE - 3 FT. MIN.

REQUIRED (INCLUDED)

INLET AIR

VENT PIPE

COLLAR ATTACHMENT

BRACKET

EXHAUST COLLAR

INLET AIR COLLAR

Note: To achieve optimum

performance of insert,

minimize or avoid bends

in exhaust vent pipe.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 37 38

Comments to this Manuals

No comments

Quadra-Fire QVI35 Owner's Manual Page 21

Comments to this Manuals

Related products and manuals for Fireplaces Quadra-Fire QVI35