Quadra-Fire QV32-A User Manual download pdf (Page 26)

STARTING

COLLAR

STOVE

SEALANT

BEAD

1 INCH

(25.4mm)

FIRST VENT

COMPONENT

If the installation is for a termination cap attached directly

to the fireplace, skip to the sections, Install Firestops and

Vent Termination.

3/8”

(9.5mm)

Venting Out the Rear Vent (See Figure 21)

Remove the installed rear seal cap from the rear starting collars

by cutting the strap at each end. Remove the insulation inside

the 5” collar. Follow the vent configuration tables accordingly.

Remove the 5” diameter heat shield from the 5” diameter collar

by sliding it out.

WARNING: THE TOP HEAT SHIELD (INSIDE

THE FIREBOX) MUST REMAIN ATTACHED IF

THE VENT SYSTEM IS ATTACHED TO THE

REAR STARTING COLLARS. SEE FIGURE 21.

Venting Out the Top Vent

Remove the top vent collar seal cap by removing the two

screws from the upper heat shield. Remove the insulation

inside BOTH the 4” diameter and 6 5/8” diameter collars.

(See Figure 21).

Remove the 4” diameter heat shield from the 4” diameter

collar by sliding it out.

You have to take the glass off for positioning the logs when

the unit is finally installed in place and finished around it. Attach

vent system to the top starting collars.

Figure 21

Insert screwdriver

or similar object

here to remove cap.

CUT HERE

Venting

Out Rear

Venting

Out Top

WARNING: THE REAR VENT COLLAR SEAL

CAP MUST REMAIN ATTACHED TO THE REAR

VENT COLLARS IF THE VENT SYSTEM IS ATTACHED

TO THE TOP STARTING COLLARS. SEE FIGURE 21.

WARNING: FAILURE TO REMOVE INSULATION

IN THE SET OF COLLARS YOU ARE USING

COULD CAUSE A FIRE.

WARNING: YOU MUST LEAVE THE INSULA-

TION IN PLACE IN THE SET OF COLLARS YOU

ARE NOT USING.

1. Attach the First Vent Component to the

Starting Collars

To attach the first vent component to the starting collars

of the fireplace:

• Apply a 3/8 inch (9.5mm) bead of stove cement around

the fireplace inner vent starting collar.

• Lock the vent components into place by sliding the con-

centric pipe sections with four (4) equally spaced interior

beads into the fireplace collar or previously installed com-

ponent end with four (4) equally spaced indented sections.

• When the internal beads of each outer pipe line up, ro-

tate the pipe section clockwise about one-quarter (1/4)

turn. The vent pipe is now locked together.

• Slide the ceramic fiber pad over the first vent section and

place it flush to the fireplace. Continue to add vent com-

ponents.

WARNING: A 3/8 INCH (9.5 MM) BEAD OF

STOVE CEMENT MUST BE PLACED AROUND

THE FIREPLACE INNER VENT STARTING COLLAR

BEFORE ATTACHING THE FIRST VENT COMPO-

NENT. FAILURE TO SEAL THIS JOINT MAY CAUSE

THE FIREPLACE TO OPERATE IMPROPERLY. SEE

THE DIAGRAM .

Figure 22. Attaching the First Vent Component

to the Starting Collars

HEAT

SHIELD

DISCARD

INSULATION

SEAL

CAP

SEAL

CAP

HEAT

SHIELD

INSULATION,

DISCARD

BOTH

PIECES

B. Installing Vent Components

After determining which set of starting collars will be used (top

or rear), follow venting instructions accordingly.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 41 42

Comments to this Manuals

No comments

Quadra-Fire QV32-A User Manual Page 26

Comments to this Manuals

Related products and manuals for Unknown Quadra-Fire QV32-A